Dynamically balanced vibratory conveyor
PSL dynamically balanced vibratory conveyor, has very little reaction force is transmitted to the ground.
Dynamically balanced vibratory conveyor use the fully balanced system. The upper and lower troughs are coupled together by springs, and mounted at the central point of the coupling on a fixed frame. Both troughs are vibrated by means of motor-driven eccentric crank action and spring-generated resonant vibration.
PSL Dynamically balanced vibratory conveyor is developed on the basis of the plastid resonance type of a new type of vibrating conveyor, besides has the advantages of the plastid resonance type, the most prominent advantage is passed to the base of inertial vibration (dynamic load) is very small, low noise, suitable for long, wide groove width of transport requirements, when the floor surface or on steel structure installation with other type of vibrating conveyor incomparable shock absorption edge.
It is suitable to be applied at vibration sensitive situation such as weighing packing machine area, upstairs, steel structure platform, high bridge way etc.
Double trough is available and can convey materials simultaneously.
In case of height of inlet is limited, lower conveying trough can be designed to replace balancing structure.
Leaf plate can be placed in the trough to reinforce cooling and loosening wet materials such as wet sugar.
The inertial vibration force (dynamic load) transmitted to the foundation is very small and low in noise
Suitable for long distance, wide groove width conveying requirements
Unmatched shock absorption advantages of other types of vibrating conveyors when installed on floor slabs or steel frame supports
If the balance body is used as the transport groove body, the upper and lower grooves can be transported at the same time, and the effect of using two vibrating conveyors can be produced without increasing equipment and space.
A screen is installed in the conveying groove to realize the classification of the material while conveying.
Dynamically balanced vibratory conveyor, with unique structure as illustrated in Fig.1, the upper trough is coupled with the counter balancing structure with direction guide beams and energy storage coil springs, they are supported at the center of the guide beam on the underbed structure.
Reacting force of the upper trough is fully balanced by the lower counter balancing structure, in case unbalanced reacting force caused by materials on the trough or any other reason, it can be re-balanced by the underbed structure and damper springs.
1. conveyor through
2. balancing stand
4. eccentric connecting rod drive
5. resonant spring;
6. elastic pendulum device
7. damping spring
8. damping seat
Fully balanced type vibration conveyor adopt unique elastic support, make delivery tub and balance the body to form a quality complete balance of double plastid resonance system, two plasmids through swinging rod coupling resonance spiral springs and elastic guide, conveying groove under the action of the vibrator, and balance the body form a resonance system, the inertia vibration resonance system to produce the basic offset in the system;
Equipment support base plate through the spring vibration isolation system based connection and installation, can change because of material flow in the tub again to reduce the unbalanced vibration, thus equipment is the basis of dynamic load is very small.
This dynamically balanced vibratory conveyor is suitable for many industries including biomass, recycling, pellet manufacturing, sawmill, plywood, OSB, food processing, and agricultural industries.
|Model||Throughput||Groove width (mm)||Trough body length（m）|
How to use:
After the installation and commissioning of the vibrating conveyor, the no-load continuous test run of not less than 8 hours should be carried out.
Pay attention to the changes of conveyor amplitude, working current and noise during operation.
After confirming that there is no abnormality, it can be put into normal operation.
The Dynamically balanced vibratory conveyor is a fixed-frequency fixed-width vibrating conveying device.
If the productivity of the conveyor is adjusted, the opening of the silo gate can be adjusted to change the feeding amount or change the eccentric position of the driving device. To achieve the purpose of adjusting the productivity of the conveyor.
During the use of the vibrating conveyor, it is necessary to regularly apply grease (No. 3 calcium-based grease) to the bearing housing and the connecting rod bearing of the drive mechanism.
Continuous operation is repeated every two weeks, and non-continuous operation is filled once a month.
Always check the fastening of each fastener and replace consumables (plate springs, coil springs, rubber springs and fasteners) for long-term damage (fatigue, defects, aging wear).
It is strictly forbidden to operate with illness
Pay attention to check the temperature rise (feel) of the bearing part of the drive mechanism
If an abnormality is found, it must be stopped immediately for inspection.
Delivery amount calculated in accordance with the calculation of transport sand (bulk density of 1.6t / m3, the moisture content of 5%) level.
Conveyor installation of tank closures, liner and bulk density of the material at different power delivery to be recalculated.
Transmission distance over 15 meters, using segmented structure, site assembly connection.